Setting up a PPTP VPN Server on Debian/Ubuntu

How to setup OpenVPN Server and Client on Ubuntu 14.04

How To Setup OpenVPN Server In 5 Minutes on Ubuntu Linux
OpenVPN is now ready to use with the new profile. This file handles configuration that should be put into place before the conventional UFW rules are loaded. Because you may come back to this step at a later time, we'll re-source the vars file. At this point, we are now ready to start openvpn services to check the status of OpenVPN server. This is the keypair the VPN server host will use to authenticate itself to clients. The most convenient way is to put everything in a single signed PKCS 12 file and export it with a paraphrase. Find the directives that set the ca , cert , and key.

Quick setup: Copy and Paste

Add VPN on client computer (Mac)

Please add more instructions here. Generating Certificates Generate certificates for the server. Another alternative is using the graphical program tinyca to create your CA. Therefore, all we have to do is creating a new file named server. First, we're going to create a couple of new scripts to be used by the openvpn server. Skipped and you can work around it by running this command: RSA Pre-systemd setup Don't forget to either reboot or run the command below.

This will restart openvpn and load the new config. Since we created a server. Getting Clients Connected This section concerns creating client certificate and key files and setting up a client configuration file. The files can then be used with OpenVPN on a client platform. For a detailed discussion of each, refer to their respective home pages.

Generating Client Certificate and Key Generating certificates and keys for a client is very similar to the process used for generating server certificates. You should have already setup your Certificate Authority and created a server certificate and keys. For Windows, the file should be named client. The file can be created using vi or other editor that can create plain text files.

Client configuration file for OpenVPN Specify that this is a client client Bridge device setting dev tap Host name and port for the server default port is note: The windows GUI seems to dislike the following rule. You may need to comment it out. Proceed to creating a VPN connection. You can use any private IP address range just make sure it is not already used in your local network and the local IP and the remote IP are in the same range.

Our main purpose of setting up this VPN server is to access website right? Finally the following rule is required to ensure websites load properly. To save the IPTables rules read this article. If you are using Linux at home refer this article. Now click connect, fire your favourite browser and go to this page to check if you are using a different IP address.

Thank you very much. I successfully setup a pptp vpn server on debian wheezy according to your post. I am getting error.. I have done exact steps you mentioned here. I have 64mb vps with Debian minimal. Can you tell me what should I type exactly for the following step? Local IP — Server ip? Remote IP — What should I type here? The remoteip takes in a range of IP addresses which will be assigned to VPN clients after a connection has been established.

It must be in the same network as the localip. Then use Open port checker to see if your modem allows port My VM local IP is Leave everything else to their defaults and click apply. Sorry for my lack of knowledge..

Hello, I found your article very helpful. I set up this server on VMware and bridged the network to my physical connection. I have also forwarded the port on my router and also enable DMZ.

Check if the ports are properly forwarded by going to the Open Port Checker and entering port I did all steps and now I can connect to pptp. Hello there, I am having problem setting a vpn server using pptpd. I have setup it accrding to your tutorial, but even though i cant connect to the server even on the internal network.

I am getting errors on windows when trying to connect says the server doesnt ansfer. I have forwarded the port in my router for remote connection but i cant even connect locally: Could i get any help on that? Also check if your firewall iptables allows incoming GRE traffic and port From windows try the following command. When i enter service pptpd status i get no output. When i connect using telnet i am getting connected but after a while i get Connection closed by foreign host.

How is the windows machine connected with the VPN server? Using a switch or is there a router in between them.

I can connect when trying on lan side but when using outside of home i receive error Check if port is open from the Internet. Hi, I got it connected connecting using bt-wifi does not work however I get no web access. It states connected but no internet pages will display even when trying dns ip instead of url.

Any further help Jesin? How I can route to a different subnet? You can configure the client system to automatically insert the route when a VPN connection is established. Dear sir very good tutorial about pptp vpn.

If possible, try with a 2nd network card. Do you use a Raspberry PI? When I connect I get this error: A connection to the remote computer could not be established, so the port used for this connection was closed.

Maybe a firewall or antivirus is blocking ports on your desktop PC. Also Check if the dedicated server allows incoming connections on port by use this tool. Very nice tutorial, was able to set it up easily!

Just wondering if you have a tutorial on setting up a VPN using certificates for authentication? Or if we are able to change this so that certificates are used to authenticate the user?

IPSEC VPN on Ubuntu 16.04 with StrongSwan